What you'll see and hear
- A flashing red MASTER WARN light and a continuous repetitive chime. It's a chime on the Airbus, not a fire bell.
- ENG 1 FIRE (or 2) in red at the top of the upper ECAM.
- The red ENG 1 FIRE pushbutton lit on the overhead, and the red FIRE light by that engine's master switch on the pedestal.
Here's how it looks on the ECAM. The red title is the warning; the blue lines are your actions:
1. Below 400 ft: fly the aircraft
- Don't touch anything on the engine yet. An engine fire isn't a memory item on the A320. Nothing gets moved from memory.
- Keep it straight with rudder if the engine loses thrust, and follow the SRS pitch bar.
- Positive climb, gear up. That's the only action below 400 ft.
- Leave the thrust levers in TOGA or FLX.
Silence it, don't rush it. Pressing MASTER WARN stops the chime so you can think. It doesn't fix anything.
2. Above 400 ft: the ECAM actions
Read each line, find the switch, confirm it's the burning engine, then move it. Flying single-pilot, say it out loud: "Thrust lever one, idle."
- Affected THR LEVER → IDLE.
- Affected ENG MASTER → OFF. This cuts the fuel. Touch it and confirm the engine before you move it.
- Affected ENG FIRE P/B → PUSH. It shuts off fuel, bleed, hydraulics and the generator for that engine, silences the chime and arms the extinguishers. The ECAM starts a 10-second countdown.
- AGENT 1 → DISCH when the countdown reaches zero.
- ATC → NOTIFY. That's your MAYDAY, below.
- Fire still showing 30 seconds after AGENT 1? AGENT 2 → DISCH.
The bottles aren't optional. In flight, AGENT 1 goes after the countdown every time, even if the red light has gone out. Only AGENT 2 depends on the fire still being there.
3. The MAYDAY call
Make it once the actions are done and the aircraft is climbing under control. Say it once, clearly, with the most important thing first.
- Fire still burning? Say "fire not out". It changes what ATC and the fire service prepare for.
- Expect ATC to ask for persons on board and fuel endurance. If you're busy, say "Stand by" and answer when you can.
- Ask for the fire service to meet you on the runway.
4. Clean up and climb on one engine
From here it flies like an engine failure: level off at engine-out acceleration altitude, retract the flaps on schedule, climb at green dot with the live engine at MCT. It's all set out in engine failure after takeoff, so we won't repeat it here.
5. LAND ASAP: get it back on the ground
- Check the STATUS page. After a fire it shows LAND ASAP in red: the nearest suitable airport.
- That's usually where you just left. If you built the return in the SEC F-PLN before departure, activate it now (how in our MCDU tutorial).
- You'll probably be overweight. That's accepted with a fire. Check the landing performance and brief the overweight landing.
- One-engine approach: CONF 3 is the safe choice. Set LDG FLAP 3 on the GPWS panel so you don't get a false warning.
Engine fire vs engine failure
| Engine fire | Engine failure | |
|---|---|---|
| Alert | Red warning, continuous chime | Amber caution, single chime |
| Engine | May still be running when it starts | Running down or stopped |
| Relight? | Never | Sometimes, if there's no damage |
| Extinguishers | AGENT 1 always, AGENT 2 if needed | Only if there's damage |
| Radio | MAYDAY | MAYDAY |
| Afterwards | LAND ASAP in red | LAND ASAP in amber |
Where simmers get it wrong
- Reaching for the overhead below 400 ft. Fly first, every time.
- Shutting down the wrong engine. Read the ECAM, touch the lever, say it, then move it.
- Skipping AGENT 1 because the light went out. In flight, it goes after the countdown regardless.
- Firing AGENT 2 straight after AGENT 1. Wait the 30 seconds and check the fire is still there.
- A long MAYDAY before the aircraft is under control. Aviate first; the call can wait 30 seconds.
- Pressing on to the destination. LAND ASAP means the nearest suitable airport.
Practise it
Arm an engine fire from the failures menu on the Fenix EFB or the MCDU, set to trigger just after takeoff, before you line up. In Flight Sim Academy, type ENG 1 FIRE into In-Flight Assistance for the actions while you fly, and the Abnormal Procedures cards give you the radio calls.
Engine fire questions
Is engine fire a memory item on the A320?
No. On the A320 an engine fire is worked from the ECAM, read and do, one line at a time. The only thing you do from memory is fly the aircraft: keep it straight, follow the SRS pitch bar and get the gear up. ECAM actions start above 400 ft.
When do I discharge the fire extinguisher in the A320?
Push the ENG FIRE pushbutton, then discharge AGENT 1 when the 10-second countdown on the ECAM ends. AGENT 2 only goes if the fire is still indicated 30 seconds after AGENT 1.
Should I declare MAYDAY or PAN PAN for an engine fire?
MAYDAY. An engine fire is a distress situation, even if the fire goes out. Say MAYDAY three times, then the station, your callsign, the problem and what you want to do.
Do I have to land straight away after an engine fire?
Yes, at the nearest suitable airport. The ECAM STATUS page will show LAND ASAP in red. That's usually your departure airport, even if you're overweight.
What if the engine fire happens before V1?
Then you reject the takeoff. Below V1 you stop, and the on-ground engine fire procedure follows once you've stopped. Above V1 you're going flying, and this guide applies.
How do I practise an engine fire in the Fenix?
Set it from the failures menu on the Fenix EFB or the MCDU, armed to trigger just after takeoff, so it catches you mid-climb rather than when you're ready for it.
Red light at rotation? Know the order.
Start free with Pre-Flight and Cockpit Preparation. Unlock all 21 phases, In-Flight Assistance and 13 abnormal procedures for £9.99, once.